JOB DESCRIPTION – IN-PROCESS INSPECTION & QUALITY CONTROL EXECUTIVE
1. Position Details
Position: In-Process Inspection & Quality Control Executive
Department: Quality / Manufacturing
Industry: Automobile Components – CNC Machining
Location: Manufacturing Plant
Reports To: Quality Manager / Plant Head
Works Closely With: Production, CNC Operators, Setters, Maintenance, Stores, PPC & Dispatch.
Job Purpose
To ensure that all components manufactured on the shop floor conform to approved drawings, specifications, Control Plans and customer requirements through effective in-process inspection and process control.
The position is responsible for identifying quality deviations at the earliest stage, preventing defective production, maintaining inspection records and supporting Production in achieving zero-defect manufacturing.3. Key Responsibilities
A. In-Process Inspection
Conduct in-process inspection of CNC machined components as per approved drawings, Control Plans and inspection standards.
Check critical dimensions, tolerances, surface finish and other specified characteristics.
Identify process deviations and immediately communicate them to Production/Quality.
B. First Piece / Setup Approval
Perform first-piece inspection after machine setup, tool change or process adjustment.
Verify dimensions against drawings and approved specifications before allowing regular production.
Approve or hold production based on inspection results.
C. Patrol / Periodic Inspection
Conduct regular patrol inspections on the shop floor.
Monitor process consistency and identify trends or deviations.
Ensure inspection frequency is followed as per the Control Plan.
D. Measuring Instruments & Gauges
Ensure correct usage and handling of measuring equipment, including:
Vernier Calipers
Micrometers
Bore Gauges
Height Gauges
Dial Gauges
Thread Gauges
Plug Gauges
Ring Gauges
Snap Gauges
Depth Gauges
Profile Projector
Surface Roughness Tester
Other gauges and inspection equipment applicable to the plant
4. Process Quality Control
Monitor process parameters and product characteristics.
Ensure production is carried out according to approved Process Flow, Control Plan and Work Instructions.
Identify recurring defects and support corrective/preventive actions.
Prevent defective components from moving to the next process.
5. Rejection & Non-Conforming Product Control
Identify, segregate and properly label rejected/non-conforming components.
Maintain rejection and rework records.
Ensure non-conforming material is not mixed with accepted production.
Coordinate with Production and Quality for disposition and corrective action.
6. SPC & Process Monitoring
Perform basic SPC activities for critical dimensions.
Monitor process trends and variation.
Support calculation and monitoring of Cp/Cpk where applicable.
Escalate abnormal trends before they result in rejection.
7. Documentation & Records
Maintain in-process inspection reports, first-piece approval records and patrol inspection records.
Ensure all records are properly completed, signed/authorized and maintained as per the companys document-control system.
Maintain records related to rejection, rework, inspection and corrective actions.
8. Drawing & Specification Interpretation
Read and interpret engineering drawings, specifications and inspection standards.
Understand dimensional tolerances, surface finish requirements and basic GD&T.
Pay special attention to critical dimensions, special characteristics and customer-designated characteristics.
9. Coordination With Production
Work closely with CNC Operators, Setters and Production Supervisors to resolve quality issues.
Communicate inspection results and deviations promptly.
Support Production in reducing rejection, rework and process variation.
Ensure quality requirements are understood and followed on the shop floor.
10. Customer Complaint & Corrective Action Support
Support investigation of customer complaints related to product quality.
Assist in root-cause analysis using 5 Why, Fishbone, Pareto and other quality tools.
Support implementation and verification of corrective and preventive actions.
11. IATF 16949 & Quality System Compliance
Follow applicable requirements of the companys Quality Management System.
Maintain compliance with IATF 16949 procedures and work instructions.
Support internal/external audits by providing required inspection and quality records.
Ensure adherence to inspection and calibration procedures.
12. 5S, Safety & Shop-Floor Discipline
Maintain proper 5S and cleanliness in the inspection and production areas.
Follow all safety procedures and company policie
Ensure proper handling, storage and protection of measuring instruments and gauges.
13. Primary Objective
“Do not allow a defect to move to the next process or reach the customer.”14. Qualification
Preferred:
Diploma / ITI / B.E. / B.Tech in Mechanical, Production, Manufacturing or Automobile Engineering.
Diploma in Mechanical Engineering with relevant machining-quality experience may also be considered.
15. Experience
Preferred Experience: 2–6 Years
Experience in any of the following industries/processes will be preferred:
Automobile Component Manufacturing
CNC Machining
CNC Turning
Precision Turned Components
Auto Ancillary Industry
Tier-1 / Tier-2 Automotive Suppliers
Candidates with practical experience in CNC in-process inspection will be preferred.16. Technical Skills
The candidate should have practical knowledge of:
Engineering Drawing Reading
Dimensional Inspection
Basic GD&T
Vernier & Micrometer Measurement
Gauges & Inspection Equipment
CNC Machining Processes
Control Plan
Process Flow
Inspection Standards
SPC
Cp/Cpk
7 QC Tools
5 Why Analysis
Fishbone Analysis
Pareto Analysis
Basic MSA
Calibration System
Non-Conforming Product Control
IATF 16949 Requirements
Key Competency
Strong attention to detail, practical shop-floor inspection skills, quick identification of quality deviations, effective coordination with Production and a strong commitment to zero-defect manufacturing.
Interested candidates can share their updated CV for consideration.
Mobile: 9718009162 / 9873749599
Email: info@divyaplacement.com
Regards,
Mukesh Yadav & Brijesh Kandpal
Divya Placement Consultants
Job Code: 9772
Gender: Male
Experience: 2
Education: Diploma / ITI / B.E. / B.Tech in Mechanica
Salary: 25000
Job Location: WAZIRPUR FARIDABAD
Recruiter Name: MR. MUKESH YADAV
Number: 9891270425
Email: info@divyaplacement.com
